Hot Tub Forum
Original => Hot Tub Forum => Topic started by: COWBOY on December 18, 2008, 02:19:57 pm
-
I HAVE JUST RECENTLY PUCHASED A HOT SPRINGS JETSETTER & WAS WONDERING DOES THE SPA ITSELF ACTUALLY DO ANYTHING DIFFERENT WHEN YOU PUSH THE CLEAN BUTTON OR IS IT STRICKLY JUST A 10 MIN. TIME OFF FUNCTION?
-
Strictly a 10 minute cycle. The idea is to push the clean button, add your chems, cover the spa back up and be done. That way, you don't have to go back out to the spa and turn it off or cover it up.
I use mine as a 10 minute timer for the jets while I'm in as well. That way, when I'm really relaxed after 10 minutes of massage, I don't have to move to turn off the jets. Lazy, yes, convenient, absolutely.
-
Vanguard, don't you keep the spa cover open after adding the chems? The experts say that it will prolong the life of the cover but it sure wastes electricity when it's cold outside......
-
You know, I know you're supposed to, but I don't. I'm usually just adding MPS after I soak. My cover has been fine.
My only issue with my cover was when I had a pair of wire cutters sitting on it and my son stepped on the cutters and punctured the cover. Wasn't long before I needed another cover. I've had that one since and it is still fine. Been at least four years since that happened.
-
You only have to leave the cover open if you're shocking the spa. This allows the chlorine to oxidize out and not into your cover. Just balancing pH or alk is totally fine to close it up.
For clarity, is there a difference between this "clean cycle" and just turning the jets on and walking away? Don't most spas have a 15 or 20 min cycle on high speed? :-/
Steve
-
You only have to leave the cover open if you're shocking the spa. This allows the chlorine to oxidize out and not into your cover. Just balancing pH or alk is totally fine to close it up.
For clarity, is there a difference between this "clean cycle" and just turning the jets on and walking away? Don't most spas have a 15 or 20 min cycle on high speed? :-/
Steve
Yes they do.
-
You only have to leave the cover open if you're shocking the spa. This allows the chlorine to oxidize out and not into your cover. Just balancing pH or alk is totally fine to close it up.
For clarity, is there a difference between this "clean cycle" and just turning the jets on and walking away? Don't most spas have a 15 or 20 min cycle on high speed? :-/
Steve
The "Clean" button turns on a jet pump for 10 min. If you turn the jets on and walk away it will run for 2 hours.
-
You only have to leave the cover open if you're shocking the spa. This allows the chlorine to oxidize out and not into your cover. Just balancing pH or alk is totally fine to close it up.
For clarity, is there a difference between this "clean cycle" and just turning the jets on and walking away? Don't most spas have a 15 or 20 min cycle on high speed? :-/
Steve
What about adding a small amount of dichlor after each soak? Is it safe to close the cover with the pumps running after adding a teaspoon or two of dichlor?
-
The "Clean" button turns on a jet pump for 10 min. If you turn the jets on and walk away it will run for 2 hours.
That's incorrect soak king. On high speed, they will run for a 15 minute cycle. If you turn the pump on at low speed, it will run 2 hours. After adding chemicals, high speed makes more sense due to the above.
Gombo; Just adding a small amount to boost the reading is fine. Only when shocking do you need to be concerned about the cover.
So then there's no difference at all between this cycle on most every spa and HotSprings clean cycle? These guys are marketing guru's! ;D
-
Last time I checked, even on Hot Spring, if you run the high speed pump it will run for two hours before shutting off. Maybe other brands will shut off after 15, but I'm pretty sure HS will run for the two hours.
-
Soak-king is correct.
When you hit the "Jets" button on a HotSpring Spa, the jet pump will run on high speed for 2 hours and then shut off.
When you hit the "Clean" button, the jet pump will run on high speed for 10 minutes and then shut off.
It's nice being able to sit in the spa an hour or two without having to restart the pumps every 15 minutes or so.
Term
-
Soak-king is correct.
Term
Hey!!! I was right, too!! :(
-
Doesn't the clean button only activate ONE jet pump?
There is a Jets 1 button and a Jets 2 button.
Then, it doesn't get the water that is in the water feature.
I have an old pool cover that I cut to fit for a blanket. It bunches up when the jets are on, therefore I do not use the clean button ever. I bring my dichlor out in an old film case (I can't remember whose idea that was?) dump it in, keep everything running, set the kitchen timer, then go back out after 10 minutes to close it up. That way, I know that ALL the water is clean!
After 2 years, my cover still looked brand new and there was NO water in my cover foam.
-
Yes, it only activates one pump.
-
Chlorine forms ions when you add it to the water. When those ions are formed, they want to get as far away from each other as possible. The chlorine you add to the water basically shoots itself through the whole tub once it forms that ion.
Which is great if your tub goes down for some reason, you can still keep some sanitizer in it.
-
Getting back to the actual topic about the clean button, one of my customers calls it his snooze button. According to him, he used to hit his snooze 2 or 3 times every morning before he got up and got cleaned up for work.
Since he's had his Sovereign, he gets up at the first alarm, grabs a cup of coffee, hops in his tub, and hits the clean button. Once it goes off he knows it's time for him to get in the shower and get ready for work.
Not necessarily what Hot Spring had in mind when they put it on there, but another great use for it!